Lash Lift Accessories and Tools

Apply Primer: Dispense a small amount onto a microswab and apply evenly through clean, dry lashes from base to tip. Allow the lashes a moment to absorb the primer, ensuring the nutrients penetrate deeply for enhanced resilience and health.

Proceed with Lash Lift or Tint: With lashes fully prepared and protected, proceed with your lash lift or tint application, achieving superior results with enhanced safety.

Incorporate our "Prep X Protect" into your lash lift and tint service to leverage the benefits of these high-quality ingredients, ensuring every lash lift and tint not only looks stunning but also promotes lash health and longevity.

Preparation: Before opening, gently massage the lash lift sachet to ensure the lotion is well mixed and warmed up to room temperature for optimal performance. 

Open Sachet: Each packet contains enough product for 2-3 services. To extend usability & maintain effectiveness, carefully poke a small hole in the sachet or cut a very small opening at the top of the packet. This reduces exposure to oxygen, preventing the lotion from oxidation and becoming less effective.

Dispense & Seal: Dispense the amount needed for a single service. Immediately after dispensing, seal the opening with silicone tape to prevent any leaks.

Apply: Apply the lift lotion from the base to ⅔ of the way up the lashes. Ensure to avoid the tips of the lashes, as it can cause over-processing. Allow the lift lotion to process based on the lash thickness. We recommend using the “bend test” to assess the readiness of the lashes. 

Remove: Once the processing time is complete, remove the lotion thoroughly. Continue with Set x Tint.

Tip: If using balm adhesive (containing natural oils), you may need to increase processing time by 20-30% as the balm can create a layer over the lashes, slowing the penetration of lash lift solution into the lashes.

Processing Time for ORIGINAL Lift Lotion

3 Minutes for Fine Lashes 

4 Minutes for Medium Lashes 

5 Minutes for Thick Lashes 

6-7 Minutes for Very Thick Lashes

Processing Time for TGA-FREE Lift Lotion

4-5 Minutes for Fine Lashes 

6-7 Minutes for Medium Lashes 

8-9 Minutes for Thick Lashes 

10-11 Minutes for Very Thick Lashes

Preparation of Sachet: Before opening, gently massage the lash lift sachet to ensure the lotion is well mixed and warmed up to room temperature for optimal performance. 

Open Sachet: Each packet contains enough product for 2-3 services. To extend usability & maintain effectiveness, carefully poke a small hole in the sachet or cut a very small opening at the top of the packet. This reduces exposure to oxygen, preventing the lotion from oxidation and becoming less effective.

Dispense & Seal: Dispense the amount needed for a single service. Immediately after dispensing, seal the opening with silicone tape to prevent any leaks.

Mix Set x Tint Lotion with Tint: Mix equal amounts of Set X Tint Lotion with your favorite tint color (note: do not add your developer to this mixture).

Apply Mixture: Apply the mixed lotion onto the entire lash, from base to tip.

Processing Time: Allow the mixture to process, adjusting the time based on the thickness of the lashes.

Remove and Rinse: After the processing time is complete, thoroughly remove the solution and rinse the lashes.

Proceed with Desired Lash Treatment: “24 Karat Glaze + Keratin Sealant Duo” OR Power Gloss.

Tip: Ensure there is a sufficient amount of mixture on the lashes. Cover with lift paper during the process to prevent the lotion from drying out, achieving optimal results.

Processing Time

3 Minutes for Fine Lashes 

4 Minutes for Medium Lashes 

5 Minutes for Thick Lashes 

6-7 Minutes for Very Thick Lashes

Condition and nourish the lashes with our 24 Karat Glaze + Keratin Sealant Duo (Non-Vegan) OR Power Gloss (Vegan).